First off thanks to JetDog who I first saw posted about this incredible feeder. I've been using it for the past couple months and I will NEVER EVER go back to any other kind of feeder!
I started out with the basic red/white plastic feeder that all the feed stores sell............ the chickens wasted more food than they ate so I knew I had to figure out something else.
I then made a PVC tube feeder, but it only held a few pounds of food and seemed to need to be refilled all the time..... and I only have 5 chickens
So then I read about the 5 gallon bucket feeder from Jetdog.................... And I've never turned back!
This thing is SOOO easy to make and it will hold 25 lbs of pellet food!!!
First thing you need is a 5 gallon bucket. You can purchase one at one of the home improvement stores, or if you want to save a few bucks like me you can get a used pickle bucket from your local fast food restaurant for free, or even try your local bakery for a 5 gallon frosting bucket.
Next you need 3' pvc elbow (about $3 at Lowes) and a 3-1/2' hole saw (you can get the hole saw cheap at Harbor Freight).
Cut the end of the elbow off at the red line (see pic below) and then figure out where the hole in the bucket should be so that when you stick the CUT END into the bucket it's about 3/4' off the bottom. Silicone or pvc cement around inside and out, put the top on the bucket and you're set!
I also added an 'extension' to the end of the elbow that the chickens stick their heads in to get the food to make the hole a bit smaller and also so that they have to go farther in. This TOTALLY eliminated ALL spilled pellets! The 'extension' adds about 1' deeper they need to go. See pictures below.
I put the bucket on a few patio bricks to bring it up to about chest height on my chickens.
My bucket only has 1 elbow but you could probably add up to 3 if you wanted to feed around the entire bucket.
You can see the extension (3' PVC pipe that I added to the elbow in the picture below)
Here is a picture of the bucket in my coop via my coop web cam.
Picture from inside the bucket
Here is the finished product sitting next to my 5 gallon heated water for the winter. There's a link in my signature below for instructions on the waterer.
Another BYC friend of mine (LoneOak) suggested using a 'Street Elbow' - I think his idea might work better. -
I used a street elbow in mine which has two different kinds of ends. I cut off the hub end and inserted the spigot end into the bucket. Then I cleaned up the hub end and put it over the spigot end (with the elbow still attached) and pushed it tight against the bucket. The hub fits securely over the spigot holding it all together without any fasteners or glue.
Once you make and use this type of feeder you will NEVER use anything else again!!!!!!!!!!
I started out with the basic red/white plastic feeder that all the feed stores sell............ the chickens wasted more food than they ate so I knew I had to figure out something else.
I then made a PVC tube feeder, but it only held a few pounds of food and seemed to need to be refilled all the time..... and I only have 5 chickens
So then I read about the 5 gallon bucket feeder from Jetdog.................... And I've never turned back!
This thing is SOOO easy to make and it will hold 25 lbs of pellet food!!!
First thing you need is a 5 gallon bucket. You can purchase one at one of the home improvement stores, or if you want to save a few bucks like me you can get a used pickle bucket from your local fast food restaurant for free, or even try your local bakery for a 5 gallon frosting bucket.
Next you need 3' pvc elbow (about $3 at Lowes) and a 3-1/2' hole saw (you can get the hole saw cheap at Harbor Freight).
Cut the end of the elbow off at the red line (see pic below) and then figure out where the hole in the bucket should be so that when you stick the CUT END into the bucket it's about 3/4' off the bottom. Silicone or pvc cement around inside and out, put the top on the bucket and you're set!
I also added an 'extension' to the end of the elbow that the chickens stick their heads in to get the food to make the hole a bit smaller and also so that they have to go farther in. This TOTALLY eliminated ALL spilled pellets! The 'extension' adds about 1' deeper they need to go. See pictures below.
I put the bucket on a few patio bricks to bring it up to about chest height on my chickens.
My bucket only has 1 elbow but you could probably add up to 3 if you wanted to feed around the entire bucket.
You can see the extension (3' PVC pipe that I added to the elbow in the picture below)
Here is a picture of the bucket in my coop via my coop web cam.
Picture from inside the bucket
Here is the finished product sitting next to my 5 gallon heated water for the winter. There's a link in my signature below for instructions on the waterer.
Another BYC friend of mine (LoneOak) suggested using a 'Street Elbow' - I think his idea might work better. -
I used a street elbow in mine which has two different kinds of ends. I cut off the hub end and inserted the spigot end into the bucket. Then I cleaned up the hub end and put it over the spigot end (with the elbow still attached) and pushed it tight against the bucket. The hub fits securely over the spigot holding it all together without any fasteners or glue.
Once you make and use this type of feeder you will NEVER use anything else again!!!!!!!!!!
First off thanks to JetDog who I first saw posted about this incredible feeder. I've been using it for the past couple months and I will NEVER EVER go back to any other kind of feeder!
I started out with the basic red/white plastic feeder that all the feed stores sell............ the chickens wasted more food than they ate so I knew I had to figure out something else.
I then made a PVC tube feeder, but it only held a few pounds of food and seemed to need to be refilled all the time..... and I only have 5 chickens
So then I read about the 5 gallon bucket feeder from Jetdog.................... And I've never turned back!
This thing is SOOO easy to make and it will hold 25 lbs of pellet food!!!
First thing you need is a 5 gallon bucket. You can purchase one at one of the home improvement stores, or if you want to save a few bucks like me you can get a used pickle bucket from your local fast food restaurant for free, or even try your local bakery for a 5 gallon frosting bucket.
Next you need 3' pvc elbow (about $3 at Lowes) and a 3-1/2' hole saw (you can get the hole saw cheap at Harbor Freight).
Cut the end of the elbow off at the red line (see pic below) and then figure out where the hole in the bucket should be so that when you stick the CUT END into the bucket it's about 3/4' off the bottom. Silicone or pvc cement around inside and out, put the top on the bucket and you're set!
I also added an 'extension' to the end of the elbow that the chickens stick their heads in to get the food to make the hole a bit smaller and also so that they have to go farther in. This TOTALLY eliminated ALL spilled pellets! The 'extension' adds about 1' deeper they need to go. See pictures below.
I put the bucket on a few patio bricks to bring it up to about chest height on my chickens.
My bucket only has 1 elbow but you could probably add up to 3 if you wanted to feed around the entire bucket.
You can see the extension (3' PVC pipe that I added to the elbow in the picture below)
Here is a picture of the bucket in my coop via my coop web cam.
Picture from inside the bucket
Here is the finished product sitting next to my 5 gallon heated water for the winter. There's a link in my signature below for instructions on the waterer.
Another BYC friend of mine (LoneOak) suggested using a 'Street Elbow' - I think his idea might work better. -
I used a street elbow in mine which has two different kinds of ends. I cut off the hub end and inserted the spigot end into the bucket. Then I cleaned up the hub end and put it over the spigot end (with the elbow still attached) and pushed it tight against the bucket. The hub fits securely over the spigot holding it all together without any fasteners or glue.
Once you make and use this type of feeder you will NEVER use anything else again!!!!!!!!!!
I started out with the basic red/white plastic feeder that all the feed stores sell............ the chickens wasted more food than they ate so I knew I had to figure out something else.
I then made a PVC tube feeder, but it only held a few pounds of food and seemed to need to be refilled all the time..... and I only have 5 chickens
So then I read about the 5 gallon bucket feeder from Jetdog.................... And I've never turned back!
This thing is SOOO easy to make and it will hold 25 lbs of pellet food!!!
First thing you need is a 5 gallon bucket. You can purchase one at one of the home improvement stores, or if you want to save a few bucks like me you can get a used pickle bucket from your local fast food restaurant for free, or even try your local bakery for a 5 gallon frosting bucket.
Next you need 3' pvc elbow (about $3 at Lowes) and a 3-1/2' hole saw (you can get the hole saw cheap at Harbor Freight).
Cut the end of the elbow off at the red line (see pic below) and then figure out where the hole in the bucket should be so that when you stick the CUT END into the bucket it's about 3/4' off the bottom. Silicone or pvc cement around inside and out, put the top on the bucket and you're set!
I also added an 'extension' to the end of the elbow that the chickens stick their heads in to get the food to make the hole a bit smaller and also so that they have to go farther in. This TOTALLY eliminated ALL spilled pellets! The 'extension' adds about 1' deeper they need to go. See pictures below.
I put the bucket on a few patio bricks to bring it up to about chest height on my chickens.
My bucket only has 1 elbow but you could probably add up to 3 if you wanted to feed around the entire bucket.
You can see the extension (3' PVC pipe that I added to the elbow in the picture below)
Here is a picture of the bucket in my coop via my coop web cam.
Picture from inside the bucket
Here is the finished product sitting next to my 5 gallon heated water for the winter. There's a link in my signature below for instructions on the waterer.
Another BYC friend of mine (LoneOak) suggested using a 'Street Elbow' - I think his idea might work better. -
I used a street elbow in mine which has two different kinds of ends. I cut off the hub end and inserted the spigot end into the bucket. Then I cleaned up the hub end and put it over the spigot end (with the elbow still attached) and pushed it tight against the bucket. The hub fits securely over the spigot holding it all together without any fasteners or glue.
Once you make and use this type of feeder you will NEVER use anything else again!!!!!!!!!!
Page 1 of 3 Lynchburg Graded Feeder Cattle Sale - Rustburg, VA AMS Livestock, Poultry, & Grain Market News. 25 532-545 544 116.00-124.00 123.37 7 640 640 114.00 114.00.
Feeder 3 7 25 20
- Construction Monkey calculator that determines an electrical feeder based on load size as well as other variables. It also calculates the voltage drop and maximum distances of the feeders.
- 25 (7.6) ArcLink ®/Linc-Net Control. (Comes installed on feeder) K1500-2 K1500-3 K1500-4 K1500-5 K489-7 Lincoln Electric Compatible gun connector kits K466-1 K613.
- Roz Purcell is a bestselling cookery author and entrepreneur. Roz has successfully launched a stellar media career which includes a winning role on Come Dine with Me Ireland, a guest chef appearance on TV3's the Restaurant, and a stint as a Celebrity Bainisteor on RTE. Her passion for healthy food and lifestyle has earned her thousands of followers on social media in recent years.
